DIY solution to test for a slow leak in a tire?
I have a slow leak in one tire; every couple of weeks it's down to 18PSI from the desired 30PSI. I'd like to find the leak, but I'd rather not pay $$ for some "professional" soap solution to detect it.
What's a quick-and-dirty DIY solution for detecting slow air leaks? Would I apply it with a sprayer? And, while I'm at it, what kind of bubble production would constitute a "small" leak; a 1/2" bubble per second? a 1/4" bubble per minute?
tires leak
edited Dec 20 at 17:49
Pᴀᴜʟsᴛᴇʀ2♦
108k16163356
asked Dec 20 at 17:35
Daniel Griscom
4811520
add a comment |
I have a slow leak in one tire; every couple of weeks it's down to 18PSI from the desired 30PSI. I'd like to find the leak, but I'd rather not pay $$ for some "professional" soap solution to detect it.
What's a quick-and-dirty DIY solution for detecting slow air leaks? Would I apply it with a sprayer? And, while I'm at it, what kind of bubble production would constitute a "small" leak; a 1/2" bubble per second? a 1/4" bubble per minute?
tires leak
edited Dec 20 at 17:49
Pᴀᴜʟsᴛᴇʀ2♦
108k16163356
asked Dec 20 at 17:35
Daniel Griscom
4811520
add a comment |
I have a slow leak in one tire; every couple of weeks it's down to 18PSI from the desired 30PSI. I'd like to find the leak, but I'd rather not pay $$ for some "professional" soap solution to detect it.
What's a quick-and-dirty DIY solution for detecting slow air leaks? Would I apply it with a sprayer? And, while I'm at it, what kind of bubble production would constitute a "small" leak; a 1/2" bubble per second? a 1/4" bubble per minute?
tires leak
edited Dec 20 at 17:49
Pᴀᴜʟsᴛᴇʀ2♦
108k16163356
asked Dec 20 at 17:35
Daniel Griscom
4811520
I have a slow leak in one tire; every couple of weeks it's down to 18PSI from the desired 30PSI. I'd like to find the leak, but I'd rather not pay $$ for some "professional" soap solution to detect it.
What's a quick-and-dirty DIY solution for detecting slow air leaks? Would I apply it with a sprayer? And, while I'm at it, what kind of bubble production would constitute a "small" leak; a 1/2" bubble per second? a 1/4" bubble per minute?
tires leak
tires leak
edited Dec 20 at 17:49
Pᴀᴜʟsᴛᴇʀ2♦
108k16163356
asked Dec 20 at 17:35
Daniel Griscom
4811520
edited Dec 20 at 17:49
Pᴀᴜʟsᴛᴇʀ2♦
108k16163356
asked Dec 20 at 17:35
Daniel Griscom
4811520
edited Dec 20 at 17:49
Pᴀᴜʟsᴛᴇʀ2♦
108k16163356
edited Dec 20 at 17:49
Pᴀᴜʟsᴛᴇʀ2♦
108k16163356
edited Dec 20 at 17:49
Pᴀᴜʟsᴛᴇʀ2♦
108k16163356
108k16163356
asked Dec 20 at 17:35
Daniel Griscom
4811520
asked Dec 20 at 17:35
Daniel Griscom
4811520
asked Dec 20 at 17:35
Daniel Griscom
4811520
4811520
add a comment |
add a comment |
2 Answers
2
active
oldest
votes
What's a quick-and-dirty DIY solution for detecting slow air leaks?
If you take the tire off and just visually inspect it prior to putting soap on it, you'll most likely find the culprit (ie: nail, screw, etc).
If you don't find a "smoking gun", mix a solution of a small amount of dish washing liquid into water. Maybe 20-30:1 (liquid to water)? It doesn't take a large amount of the soap for it to create bubbles. Take the offending tire off of the car and liberally spray an area of the tire. Soak one area of the tire, look and watch for bubbles, then move on to the next area. Ensure you do the sides at the bead as well as the valve stem.
Would I apply it with a sprayer?
Yes. I'd prefer a fine mist over a stream, but either should work just fine.
And, while I'm at it, what kind of bubble production would constitute a "small" leak; a 1/2" bubble per second? a 1/4" bubble per minute?
Any noticeable leak is a "big" leak. IOW, any amount of formed bubbles is too much. I'd suggest if your leak is as slow as you're suggesting, there won't be a huge bubble factory going on, so you'll need to pay close attention.
answered Dec 20 at 17:48
Pᴀᴜʟsᴛᴇʀ2♦
108k16163356
2
If it is an alloy, then checking the rim is also advised - alloys can have splits or become porous....
– Solar Mike
Dec 20 at 17:50
@SolarMike - Good point ... the tire isn't always to blame.
– Pᴀᴜʟsᴛᴇʀ2♦
Dec 20 at 17:51
add a comment |
There are 3 methods I would use.
1 - Visual inspection for foreign objects or physical damage
2 - Use a large tub, fill it up with water. Pump up your tire with air. You may want to go above what you would normally use on your car, but be sure to stay below the maximum pressure rating written on the sidewall. Higher pressure usually means a faster leak and makes it easier to find. Place the wheel in the tub of water. You may only be able to get part of the wheel in at a time. This is fine as long as it covers the bead. Watch for bubbles. If the wheel cannot be completely covered, leave ti at one spot for a minute while carefully watching, then rotate and repeat.
3 - For leaks around the bead or fill valve, you can use a bubble solution. Spray it on from a bottle, or brush it on. Home improvement stores sell bubble solutions for leak detection in gas lines.
Method 3 is not as common, but can be good for a DIY if you don't have a large tub you can use.
answered Dec 20 at 18:36
rpmerf
8,3301430
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "224"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fmechanics.stackexchange.com%2fquestions%2f62073%2fdiy-solution-to-test-for-a-slow-leak-in-a-tire%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
What's a quick-and-dirty DIY solution for detecting slow air leaks?
If you take the tire off and just visually inspect it prior to putting soap on it, you'll most likely find the culprit (ie: nail, screw, etc).
If you don't find a "smoking gun", mix a solution of a small amount of dish washing liquid into water. Maybe 20-30:1 (liquid to water)? It doesn't take a large amount of the soap for it to create bubbles. Take the offending tire off of the car and liberally spray an area of the tire. Soak one area of the tire, look and watch for bubbles, then move on to the next area. Ensure you do the sides at the bead as well as the valve stem.
Would I apply it with a sprayer?
Yes. I'd prefer a fine mist over a stream, but either should work just fine.
And, while I'm at it, what kind of bubble production would constitute a "small" leak; a 1/2" bubble per second? a 1/4" bubble per minute?
Any noticeable leak is a "big" leak. IOW, any amount of formed bubbles is too much. I'd suggest if your leak is as slow as you're suggesting, there won't be a huge bubble factory going on, so you'll need to pay close attention.
answered Dec 20 at 17:48
Pᴀᴜʟsᴛᴇʀ2♦
108k16163356
2
If it is an alloy, then checking the rim is also advised - alloys can have splits or become porous....
– Solar Mike
Dec 20 at 17:50
@SolarMike - Good point ... the tire isn't always to blame.
– Pᴀᴜʟsᴛᴇʀ2♦
Dec 20 at 17:51
add a comment |
What's a quick-and-dirty DIY solution for detecting slow air leaks?
If you take the tire off and just visually inspect it prior to putting soap on it, you'll most likely find the culprit (ie: nail, screw, etc).
If you don't find a "smoking gun", mix a solution of a small amount of dish washing liquid into water. Maybe 20-30:1 (liquid to water)? It doesn't take a large amount of the soap for it to create bubbles. Take the offending tire off of the car and liberally spray an area of the tire. Soak one area of the tire, look and watch for bubbles, then move on to the next area. Ensure you do the sides at the bead as well as the valve stem.
Would I apply it with a sprayer?
Yes. I'd prefer a fine mist over a stream, but either should work just fine.
And, while I'm at it, what kind of bubble production would constitute a "small" leak; a 1/2" bubble per second? a 1/4" bubble per minute?
Any noticeable leak is a "big" leak. IOW, any amount of formed bubbles is too much. I'd suggest if your leak is as slow as you're suggesting, there won't be a huge bubble factory going on, so you'll need to pay close attention.
answered Dec 20 at 17:48
Pᴀᴜʟsᴛᴇʀ2♦
108k16163356
2
If it is an alloy, then checking the rim is also advised - alloys can have splits or become porous....
– Solar Mike
Dec 20 at 17:50
@SolarMike - Good point ... the tire isn't always to blame.
– Pᴀᴜʟsᴛᴇʀ2♦
Dec 20 at 17:51
add a comment |
What's a quick-and-dirty DIY solution for detecting slow air leaks?
If you take the tire off and just visually inspect it prior to putting soap on it, you'll most likely find the culprit (ie: nail, screw, etc).
If you don't find a "smoking gun", mix a solution of a small amount of dish washing liquid into water. Maybe 20-30:1 (liquid to water)? It doesn't take a large amount of the soap for it to create bubbles. Take the offending tire off of the car and liberally spray an area of the tire. Soak one area of the tire, look and watch for bubbles, then move on to the next area. Ensure you do the sides at the bead as well as the valve stem.
Would I apply it with a sprayer?
Yes. I'd prefer a fine mist over a stream, but either should work just fine.
And, while I'm at it, what kind of bubble production would constitute a "small" leak; a 1/2" bubble per second? a 1/4" bubble per minute?
Any noticeable leak is a "big" leak. IOW, any amount of formed bubbles is too much. I'd suggest if your leak is as slow as you're suggesting, there won't be a huge bubble factory going on, so you'll need to pay close attention.
answered Dec 20 at 17:48
Pᴀᴜʟsᴛᴇʀ2♦
108k16163356
What's a quick-and-dirty DIY solution for detecting slow air leaks?
If you take the tire off and just visually inspect it prior to putting soap on it, you'll most likely find the culprit (ie: nail, screw, etc).
If you don't find a "smoking gun", mix a solution of a small amount of dish washing liquid into water. Maybe 20-30:1 (liquid to water)? It doesn't take a large amount of the soap for it to create bubbles. Take the offending tire off of the car and liberally spray an area of the tire. Soak one area of the tire, look and watch for bubbles, then move on to the next area. Ensure you do the sides at the bead as well as the valve stem.
Would I apply it with a sprayer?
Yes. I'd prefer a fine mist over a stream, but either should work just fine.
And, while I'm at it, what kind of bubble production would constitute a "small" leak; a 1/2" bubble per second? a 1/4" bubble per minute?
Any noticeable leak is a "big" leak. IOW, any amount of formed bubbles is too much. I'd suggest if your leak is as slow as you're suggesting, there won't be a huge bubble factory going on, so you'll need to pay close attention.
answered Dec 20 at 17:48
Pᴀᴜʟsᴛᴇʀ2♦
108k16163356
edited Dec 20 at 17:50
answered Dec 20 at 17:48
Pᴀᴜʟsᴛᴇʀ2♦
108k16163356
answered Dec 20 at 17:48
Pᴀᴜʟsᴛᴇʀ2♦
108k16163356
answered Dec 20 at 17:48
Pᴀᴜʟsᴛᴇʀ2♦
108k16163356
108k16163356
2
If it is an alloy, then checking the rim is also advised - alloys can have splits or become porous....
– Solar Mike
Dec 20 at 17:50
@SolarMike - Good point ... the tire isn't always to blame.
– Pᴀᴜʟsᴛᴇʀ2♦
Dec 20 at 17:51
add a comment |
2
If it is an alloy, then checking the rim is also advised - alloys can have splits or become porous....
– Solar Mike
Dec 20 at 17:50
@SolarMike - Good point ... the tire isn't always to blame.
– Pᴀᴜʟsᴛᴇʀ2♦
Dec 20 at 17:51
2
2
If it is an alloy, then checking the rim is also advised - alloys can have splits or become porous....
– Solar Mike
Dec 20 at 17:50
If it is an alloy, then checking the rim is also advised - alloys can have splits or become porous....
– Solar Mike
Dec 20 at 17:50
@SolarMike - Good point ... the tire isn't always to blame.
– Pᴀᴜʟsᴛᴇʀ2♦
Dec 20 at 17:51
@SolarMike - Good point ... the tire isn't always to blame.
– Pᴀᴜʟsᴛᴇʀ2♦
Dec 20 at 17:51
add a comment |
There are 3 methods I would use.
1 - Visual inspection for foreign objects or physical damage
2 - Use a large tub, fill it up with water. Pump up your tire with air. You may want to go above what you would normally use on your car, but be sure to stay below the maximum pressure rating written on the sidewall. Higher pressure usually means a faster leak and makes it easier to find. Place the wheel in the tub of water. You may only be able to get part of the wheel in at a time. This is fine as long as it covers the bead. Watch for bubbles. If the wheel cannot be completely covered, leave ti at one spot for a minute while carefully watching, then rotate and repeat.
3 - For leaks around the bead or fill valve, you can use a bubble solution. Spray it on from a bottle, or brush it on. Home improvement stores sell bubble solutions for leak detection in gas lines.
Method 3 is not as common, but can be good for a DIY if you don't have a large tub you can use.
answered Dec 20 at 18:36
rpmerf
8,3301430
add a comment |
There are 3 methods I would use.
1 - Visual inspection for foreign objects or physical damage
2 - Use a large tub, fill it up with water. Pump up your tire with air. You may want to go above what you would normally use on your car, but be sure to stay below the maximum pressure rating written on the sidewall. Higher pressure usually means a faster leak and makes it easier to find. Place the wheel in the tub of water. You may only be able to get part of the wheel in at a time. This is fine as long as it covers the bead. Watch for bubbles. If the wheel cannot be completely covered, leave ti at one spot for a minute while carefully watching, then rotate and repeat.
3 - For leaks around the bead or fill valve, you can use a bubble solution. Spray it on from a bottle, or brush it on. Home improvement stores sell bubble solutions for leak detection in gas lines.
Method 3 is not as common, but can be good for a DIY if you don't have a large tub you can use.
answered Dec 20 at 18:36
rpmerf
8,3301430
add a comment |
There are 3 methods I would use.
1 - Visual inspection for foreign objects or physical damage
2 - Use a large tub, fill it up with water. Pump up your tire with air. You may want to go above what you would normally use on your car, but be sure to stay below the maximum pressure rating written on the sidewall. Higher pressure usually means a faster leak and makes it easier to find. Place the wheel in the tub of water. You may only be able to get part of the wheel in at a time. This is fine as long as it covers the bead. Watch for bubbles. If the wheel cannot be completely covered, leave ti at one spot for a minute while carefully watching, then rotate and repeat.
3 - For leaks around the bead or fill valve, you can use a bubble solution. Spray it on from a bottle, or brush it on. Home improvement stores sell bubble solutions for leak detection in gas lines.
Method 3 is not as common, but can be good for a DIY if you don't have a large tub you can use.
answered Dec 20 at 18:36
rpmerf
8,3301430
There are 3 methods I would use.
1 - Visual inspection for foreign objects or physical damage
2 - Use a large tub, fill it up with water. Pump up your tire with air. You may want to go above what you would normally use on your car, but be sure to stay below the maximum pressure rating written on the sidewall. Higher pressure usually means a faster leak and makes it easier to find. Place the wheel in the tub of water. You may only be able to get part of the wheel in at a time. This is fine as long as it covers the bead. Watch for bubbles. If the wheel cannot be completely covered, leave ti at one spot for a minute while carefully watching, then rotate and repeat.
3 - For leaks around the bead or fill valve, you can use a bubble solution. Spray it on from a bottle, or brush it on. Home improvement stores sell bubble solutions for leak detection in gas lines.
Method 3 is not as common, but can be good for a DIY if you don't have a large tub you can use.
answered Dec 20 at 18:36
rpmerf
8,3301430
answered Dec 20 at 18:36
rpmerf
8,3301430
answered Dec 20 at 18:36
rpmerf
8,3301430
answered Dec 20 at 18:36
rpmerf
8,3301430
8,3301430
add a comment |
add a comment |
Thanks for contributing an answer to Motor Vehicle Maintenance & Repair Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fmechanics.stackexchange.com%2fquestions%2f62073%2fdiy-solution-to-test-for-a-slow-leak-in-a-tire%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
