Gfrktyl

Wouldn't it be faster if there were multiple data lines (say 8) to transmit/receive data (say sequential bytes) instead of using a single line to transmit sequential bits?

It would be faster indeed if instead of one line you'd feed multiple lines at the same symbol clock.

But, USB's primary and foremost goal is to provide easy, serial (hence the S in USB) interfacing between low-cost devices (hence the U in USB) with low-cost, lightweight cabling.

So, that's why USB doesn't do parallel data lines: It's simply not the niche it's supposed to fill.

Also, don't neglect that having multiple high-speed parallel lanes requires the transceiver system to introduce a relative high amount of effort to compensate different skews on different lines, which at high rates are inevitable.

It's often become cheaper to make something work twice as fast than building two of the slower variant, unless you're really directly talking to hardware that is in its raw principle bit-parallel (e.g. DDR memory chips).

While the answer of Marcus is 100% correct, I want to add that USB 3.2 Gen 1x2 and Gen 2x2 are using two data lanes in each direction while the lanes still run at 5Gbit/s resp. 10Gbit/s each.

One of the main hurdles with any type of parallel bus is skew. If you have 8 separate wires all carrying data, it is important that all of the bits arrive at the approximately the same time. Otherwise, the bits of Byte A could get mixed up with the bits of Byte B. This means that the length of those parallel wires must be matched, within some percentage of the clock speed, so that the travel time of the signal down the wire is approximately the same. The faster the clock speed, the tighter the tolerance on the length between parallel wires.

On a PCB design for something like a motherboard, very tight design constraints are commonplace. PCB traces can achieve 1 mil or better length matching, which is good enough to implement high speed parallel interfaces. One common example of this is the DDR memory interface. This interface relies on parallel communication to move data at very high rates, but it's only possible to (affordably) implement these interfaces internally.

Imagine trying to build an external computer cable with 30+ wire connections, all length matched within a thousandth of an inch! Those cables would be very expensive compared to USB cabling.

Older computers did use a Parallel Port, which had 8 data lines but could only achieve a data rate of around 2.5 MB/s. Compare that to the 60 MB/s of USB 2.0, let alone the newer flavors of USB.

USB doesn't have Rx & Tx lines. It has one pair of differential lines, similar to RS485, with the data & clock signal encoded together. The sender sends data one way using both wires, and the receiver sends data back the other way using both lines.

Otherwise, yes, a parallel bus of signals can be very fast. Best for short distances for the reasons mentioned already.

Example of a USB data transfer:

As pointed out in other answers,

• You are right, If you use twice as many lanes, you get twice the speed.


• Earlier, parallel busses (with many data lanes) were widespread. Examples are the parallel printer interface, PATA, and PCI. But it is hard to build fast parallel busses because differences in the lengths of individual wires will cause timing differences. Parallel busses are still in widespread use on PCBs (DRAM, QSPI, GMII, ...) and on chips (AXI, AHB, QPI, ...), but for longer distances, it is actually much cheaper to build a high-speed serial link than a lower-speed parallel link with the same data throughput. Modern super-high-speed, longer-distance data links such as Gigabit Ethernet, PCIe and USB3 do have multiple data lanes, but each of those lanes is a completely independent high-speed serial link; the data streams from the individual links are combined back together at a later point. This is why you can put a PCIe x16 graphics card into a PCIe x1 slot with a fitting adapter (or sufficient violence).


• Parallel busses have more wires (duh), so cable will be thicker and heavier and more expensive, and the connector as well.

Historically, when USB was designed, high-speed data transfer was not its main focus. The main focus was to create a universal and cheap bus system for connecting peripherals like keyboards, mouses and printers.
A parallel design would have been a bad choice; it would have ruined the revolutionary small connector size and probably increased the cost of USB enough to prevent its widespread adaption.