Why does Windows 10 fail to install on UEFI/GPT laptop?












0














I'm trying to install windows 10 on a new 1TB SSD I got. fresh install, new drive, new laptop. Dell Inspiron 13 5000. Setup for UEFI. Created a bootable USB using rufus (GPT for UEFI (non CSM)). I get into setup no problem. I delete all the partitions and use diskpart to setup the drive for GPT.



I select the unallocated partition to install to. Windows created the additional partitions that it needs and then it starts the install process. Immediately, it errors with




"windows could not prepare the computer to boot into the next phase of
installation"




Spent hours googling with no luck. I haven't been able to find a log file to look at.



What can I try to determine what the problem is?



No other drives installed. legacy mode disabled. Secure boot is off. PTT is off.










share|improve this question






















  • Is UEFI set to use AHCI?
    – harrymc
    Dec 8 '18 at 18:46










  • @harrymc there isn't an option for that
    – DustinDavis
    Dec 9 '18 at 0:56










  • There must be and option for IDE/AHCI.
    – harrymc
    Dec 9 '18 at 7:53










  • @harrymc either way, windows created the partitions and it writes files but the copy process fails. So what would IDE/AHCI change? I'm guessing it's failing during the write of the boot sectors, but I turned off the security and all that.
    – DustinDavis
    Dec 10 '18 at 16:32






  • 1




    AHCI works better with GPT than IDE, which is why I suggested it. This might or might not be part of the problem.
    – harrymc
    Dec 10 '18 at 16:36
















0














I'm trying to install windows 10 on a new 1TB SSD I got. fresh install, new drive, new laptop. Dell Inspiron 13 5000. Setup for UEFI. Created a bootable USB using rufus (GPT for UEFI (non CSM)). I get into setup no problem. I delete all the partitions and use diskpart to setup the drive for GPT.



I select the unallocated partition to install to. Windows created the additional partitions that it needs and then it starts the install process. Immediately, it errors with




"windows could not prepare the computer to boot into the next phase of
installation"




Spent hours googling with no luck. I haven't been able to find a log file to look at.



What can I try to determine what the problem is?



No other drives installed. legacy mode disabled. Secure boot is off. PTT is off.










share|improve this question






















  • Is UEFI set to use AHCI?
    – harrymc
    Dec 8 '18 at 18:46










  • @harrymc there isn't an option for that
    – DustinDavis
    Dec 9 '18 at 0:56










  • There must be and option for IDE/AHCI.
    – harrymc
    Dec 9 '18 at 7:53










  • @harrymc either way, windows created the partitions and it writes files but the copy process fails. So what would IDE/AHCI change? I'm guessing it's failing during the write of the boot sectors, but I turned off the security and all that.
    – DustinDavis
    Dec 10 '18 at 16:32






  • 1




    AHCI works better with GPT than IDE, which is why I suggested it. This might or might not be part of the problem.
    – harrymc
    Dec 10 '18 at 16:36














0












0








0


1





I'm trying to install windows 10 on a new 1TB SSD I got. fresh install, new drive, new laptop. Dell Inspiron 13 5000. Setup for UEFI. Created a bootable USB using rufus (GPT for UEFI (non CSM)). I get into setup no problem. I delete all the partitions and use diskpart to setup the drive for GPT.



I select the unallocated partition to install to. Windows created the additional partitions that it needs and then it starts the install process. Immediately, it errors with




"windows could not prepare the computer to boot into the next phase of
installation"




Spent hours googling with no luck. I haven't been able to find a log file to look at.



What can I try to determine what the problem is?



No other drives installed. legacy mode disabled. Secure boot is off. PTT is off.










share|improve this question













I'm trying to install windows 10 on a new 1TB SSD I got. fresh install, new drive, new laptop. Dell Inspiron 13 5000. Setup for UEFI. Created a bootable USB using rufus (GPT for UEFI (non CSM)). I get into setup no problem. I delete all the partitions and use diskpart to setup the drive for GPT.



I select the unallocated partition to install to. Windows created the additional partitions that it needs and then it starts the install process. Immediately, it errors with




"windows could not prepare the computer to boot into the next phase of
installation"




Spent hours googling with no luck. I haven't been able to find a log file to look at.



What can I try to determine what the problem is?



No other drives installed. legacy mode disabled. Secure boot is off. PTT is off.







windows-10 uefi gpt






share|improve this question













share|improve this question











share|improve this question




share|improve this question










asked Dec 6 '18 at 23:10









DustinDavis

184212




184212












  • Is UEFI set to use AHCI?
    – harrymc
    Dec 8 '18 at 18:46










  • @harrymc there isn't an option for that
    – DustinDavis
    Dec 9 '18 at 0:56










  • There must be and option for IDE/AHCI.
    – harrymc
    Dec 9 '18 at 7:53










  • @harrymc either way, windows created the partitions and it writes files but the copy process fails. So what would IDE/AHCI change? I'm guessing it's failing during the write of the boot sectors, but I turned off the security and all that.
    – DustinDavis
    Dec 10 '18 at 16:32






  • 1




    AHCI works better with GPT than IDE, which is why I suggested it. This might or might not be part of the problem.
    – harrymc
    Dec 10 '18 at 16:36


















  • Is UEFI set to use AHCI?
    – harrymc
    Dec 8 '18 at 18:46










  • @harrymc there isn't an option for that
    – DustinDavis
    Dec 9 '18 at 0:56










  • There must be and option for IDE/AHCI.
    – harrymc
    Dec 9 '18 at 7:53










  • @harrymc either way, windows created the partitions and it writes files but the copy process fails. So what would IDE/AHCI change? I'm guessing it's failing during the write of the boot sectors, but I turned off the security and all that.
    – DustinDavis
    Dec 10 '18 at 16:32






  • 1




    AHCI works better with GPT than IDE, which is why I suggested it. This might or might not be part of the problem.
    – harrymc
    Dec 10 '18 at 16:36
















Is UEFI set to use AHCI?
– harrymc
Dec 8 '18 at 18:46




Is UEFI set to use AHCI?
– harrymc
Dec 8 '18 at 18:46












@harrymc there isn't an option for that
– DustinDavis
Dec 9 '18 at 0:56




@harrymc there isn't an option for that
– DustinDavis
Dec 9 '18 at 0:56












There must be and option for IDE/AHCI.
– harrymc
Dec 9 '18 at 7:53




There must be and option for IDE/AHCI.
– harrymc
Dec 9 '18 at 7:53












@harrymc either way, windows created the partitions and it writes files but the copy process fails. So what would IDE/AHCI change? I'm guessing it's failing during the write of the boot sectors, but I turned off the security and all that.
– DustinDavis
Dec 10 '18 at 16:32




@harrymc either way, windows created the partitions and it writes files but the copy process fails. So what would IDE/AHCI change? I'm guessing it's failing during the write of the boot sectors, but I turned off the security and all that.
– DustinDavis
Dec 10 '18 at 16:32




1




1




AHCI works better with GPT than IDE, which is why I suggested it. This might or might not be part of the problem.
– harrymc
Dec 10 '18 at 16:36




AHCI works better with GPT than IDE, which is why I suggested it. This might or might not be part of the problem.
– harrymc
Dec 10 '18 at 16:36










1 Answer
1






active

oldest

votes


















1














In my experience, this has been caused by one of two issues. First I'll offer solutions to a potentially broken installer (which I've experienced a few times over the years). Then I'll comment on the Installation Media's format at the end.



One possibility is a bug in the Disk Partitioning by the Windows installer, in my experience. Over the years I've seen it either utilize the wrong sector sizes or, more commonly, not set the boot partition as active. This is assuming that the failure occurs AFTER the partitions are setup which has been my experience.



To repair this, after Windows Installer sets up the partitions and fails to install, please try the following:



1) Boot with your Install drive mounted and go to the "Repair Options" section
2) Open a Command Line
3) Then type "diskpart"
4) Verify you only have the one drive by typing "list disk"
5) Type "select disk #" with # being the disk you're installing to
6) Then "list part" which will give you a list of partitions on that disk you have selected
7) Type "select part #" where # is the boot partition that the installer created but failed to install to
8) Type "active" to make that the active boot partition for this device
9) Type "exit" to finish with diskpart and let it save the changes



At this point you should be good to reboot and attempt the install again.



If at this point you're still out of luck, it is likely the installation media you are using. Since you are using a GPT USB drive, it could be conflicting with the installer's attempt to locate proper installation destinations (even with you explicitly stating yours). To remedy this, format the drive as MSDOS (good ol' FAT32) instead of GPT and try again.






share|improve this answer





















  • You can't mark the partition as active, that's for MBR only. I tried already. If I don't format the USB media as GPT, it won't boot to it.
    – DustinDavis
    Dec 7 '18 at 1:28










  • My apologies. Yeah, I did write that a little linearly then went back to adjust the beginning of the answer afterwards so my thoughts were mostly focused on the format of the USB. I've never formatted the USB as GPT before. When you use RUFUS to copy to the USB drive, what settings are auto-populated after selecting the ISO? A screenshot would help.
    – EricDAltman
    Dec 7 '18 at 18:49













Your Answer








StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "3"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);

StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});

function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: true,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: 10,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});


}
});














draft saved

draft discarded


















StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fsuperuser.com%2fquestions%2f1381492%2fwhy-does-windows-10-fail-to-install-on-uefi-gpt-laptop%23new-answer', 'question_page');
}
);

Post as a guest















Required, but never shown

























1 Answer
1






active

oldest

votes








1 Answer
1






active

oldest

votes









active

oldest

votes






active

oldest

votes









1














In my experience, this has been caused by one of two issues. First I'll offer solutions to a potentially broken installer (which I've experienced a few times over the years). Then I'll comment on the Installation Media's format at the end.



One possibility is a bug in the Disk Partitioning by the Windows installer, in my experience. Over the years I've seen it either utilize the wrong sector sizes or, more commonly, not set the boot partition as active. This is assuming that the failure occurs AFTER the partitions are setup which has been my experience.



To repair this, after Windows Installer sets up the partitions and fails to install, please try the following:



1) Boot with your Install drive mounted and go to the "Repair Options" section
2) Open a Command Line
3) Then type "diskpart"
4) Verify you only have the one drive by typing "list disk"
5) Type "select disk #" with # being the disk you're installing to
6) Then "list part" which will give you a list of partitions on that disk you have selected
7) Type "select part #" where # is the boot partition that the installer created but failed to install to
8) Type "active" to make that the active boot partition for this device
9) Type "exit" to finish with diskpart and let it save the changes



At this point you should be good to reboot and attempt the install again.



If at this point you're still out of luck, it is likely the installation media you are using. Since you are using a GPT USB drive, it could be conflicting with the installer's attempt to locate proper installation destinations (even with you explicitly stating yours). To remedy this, format the drive as MSDOS (good ol' FAT32) instead of GPT and try again.






share|improve this answer





















  • You can't mark the partition as active, that's for MBR only. I tried already. If I don't format the USB media as GPT, it won't boot to it.
    – DustinDavis
    Dec 7 '18 at 1:28










  • My apologies. Yeah, I did write that a little linearly then went back to adjust the beginning of the answer afterwards so my thoughts were mostly focused on the format of the USB. I've never formatted the USB as GPT before. When you use RUFUS to copy to the USB drive, what settings are auto-populated after selecting the ISO? A screenshot would help.
    – EricDAltman
    Dec 7 '18 at 18:49


















1














In my experience, this has been caused by one of two issues. First I'll offer solutions to a potentially broken installer (which I've experienced a few times over the years). Then I'll comment on the Installation Media's format at the end.



One possibility is a bug in the Disk Partitioning by the Windows installer, in my experience. Over the years I've seen it either utilize the wrong sector sizes or, more commonly, not set the boot partition as active. This is assuming that the failure occurs AFTER the partitions are setup which has been my experience.



To repair this, after Windows Installer sets up the partitions and fails to install, please try the following:



1) Boot with your Install drive mounted and go to the "Repair Options" section
2) Open a Command Line
3) Then type "diskpart"
4) Verify you only have the one drive by typing "list disk"
5) Type "select disk #" with # being the disk you're installing to
6) Then "list part" which will give you a list of partitions on that disk you have selected
7) Type "select part #" where # is the boot partition that the installer created but failed to install to
8) Type "active" to make that the active boot partition for this device
9) Type "exit" to finish with diskpart and let it save the changes



At this point you should be good to reboot and attempt the install again.



If at this point you're still out of luck, it is likely the installation media you are using. Since you are using a GPT USB drive, it could be conflicting with the installer's attempt to locate proper installation destinations (even with you explicitly stating yours). To remedy this, format the drive as MSDOS (good ol' FAT32) instead of GPT and try again.






share|improve this answer





















  • You can't mark the partition as active, that's for MBR only. I tried already. If I don't format the USB media as GPT, it won't boot to it.
    – DustinDavis
    Dec 7 '18 at 1:28










  • My apologies. Yeah, I did write that a little linearly then went back to adjust the beginning of the answer afterwards so my thoughts were mostly focused on the format of the USB. I've never formatted the USB as GPT before. When you use RUFUS to copy to the USB drive, what settings are auto-populated after selecting the ISO? A screenshot would help.
    – EricDAltman
    Dec 7 '18 at 18:49
















1












1








1






In my experience, this has been caused by one of two issues. First I'll offer solutions to a potentially broken installer (which I've experienced a few times over the years). Then I'll comment on the Installation Media's format at the end.



One possibility is a bug in the Disk Partitioning by the Windows installer, in my experience. Over the years I've seen it either utilize the wrong sector sizes or, more commonly, not set the boot partition as active. This is assuming that the failure occurs AFTER the partitions are setup which has been my experience.



To repair this, after Windows Installer sets up the partitions and fails to install, please try the following:



1) Boot with your Install drive mounted and go to the "Repair Options" section
2) Open a Command Line
3) Then type "diskpart"
4) Verify you only have the one drive by typing "list disk"
5) Type "select disk #" with # being the disk you're installing to
6) Then "list part" which will give you a list of partitions on that disk you have selected
7) Type "select part #" where # is the boot partition that the installer created but failed to install to
8) Type "active" to make that the active boot partition for this device
9) Type "exit" to finish with diskpart and let it save the changes



At this point you should be good to reboot and attempt the install again.



If at this point you're still out of luck, it is likely the installation media you are using. Since you are using a GPT USB drive, it could be conflicting with the installer's attempt to locate proper installation destinations (even with you explicitly stating yours). To remedy this, format the drive as MSDOS (good ol' FAT32) instead of GPT and try again.






share|improve this answer












In my experience, this has been caused by one of two issues. First I'll offer solutions to a potentially broken installer (which I've experienced a few times over the years). Then I'll comment on the Installation Media's format at the end.



One possibility is a bug in the Disk Partitioning by the Windows installer, in my experience. Over the years I've seen it either utilize the wrong sector sizes or, more commonly, not set the boot partition as active. This is assuming that the failure occurs AFTER the partitions are setup which has been my experience.



To repair this, after Windows Installer sets up the partitions and fails to install, please try the following:



1) Boot with your Install drive mounted and go to the "Repair Options" section
2) Open a Command Line
3) Then type "diskpart"
4) Verify you only have the one drive by typing "list disk"
5) Type "select disk #" with # being the disk you're installing to
6) Then "list part" which will give you a list of partitions on that disk you have selected
7) Type "select part #" where # is the boot partition that the installer created but failed to install to
8) Type "active" to make that the active boot partition for this device
9) Type "exit" to finish with diskpart and let it save the changes



At this point you should be good to reboot and attempt the install again.



If at this point you're still out of luck, it is likely the installation media you are using. Since you are using a GPT USB drive, it could be conflicting with the installer's attempt to locate proper installation destinations (even with you explicitly stating yours). To remedy this, format the drive as MSDOS (good ol' FAT32) instead of GPT and try again.







share|improve this answer












share|improve this answer



share|improve this answer










answered Dec 7 '18 at 0:27









EricDAltman

344




344












  • You can't mark the partition as active, that's for MBR only. I tried already. If I don't format the USB media as GPT, it won't boot to it.
    – DustinDavis
    Dec 7 '18 at 1:28










  • My apologies. Yeah, I did write that a little linearly then went back to adjust the beginning of the answer afterwards so my thoughts were mostly focused on the format of the USB. I've never formatted the USB as GPT before. When you use RUFUS to copy to the USB drive, what settings are auto-populated after selecting the ISO? A screenshot would help.
    – EricDAltman
    Dec 7 '18 at 18:49




















  • You can't mark the partition as active, that's for MBR only. I tried already. If I don't format the USB media as GPT, it won't boot to it.
    – DustinDavis
    Dec 7 '18 at 1:28










  • My apologies. Yeah, I did write that a little linearly then went back to adjust the beginning of the answer afterwards so my thoughts were mostly focused on the format of the USB. I've never formatted the USB as GPT before. When you use RUFUS to copy to the USB drive, what settings are auto-populated after selecting the ISO? A screenshot would help.
    – EricDAltman
    Dec 7 '18 at 18:49


















You can't mark the partition as active, that's for MBR only. I tried already. If I don't format the USB media as GPT, it won't boot to it.
– DustinDavis
Dec 7 '18 at 1:28




You can't mark the partition as active, that's for MBR only. I tried already. If I don't format the USB media as GPT, it won't boot to it.
– DustinDavis
Dec 7 '18 at 1:28












My apologies. Yeah, I did write that a little linearly then went back to adjust the beginning of the answer afterwards so my thoughts were mostly focused on the format of the USB. I've never formatted the USB as GPT before. When you use RUFUS to copy to the USB drive, what settings are auto-populated after selecting the ISO? A screenshot would help.
– EricDAltman
Dec 7 '18 at 18:49






My apologies. Yeah, I did write that a little linearly then went back to adjust the beginning of the answer afterwards so my thoughts were mostly focused on the format of the USB. I've never formatted the USB as GPT before. When you use RUFUS to copy to the USB drive, what settings are auto-populated after selecting the ISO? A screenshot would help.
– EricDAltman
Dec 7 '18 at 18:49




















draft saved

draft discarded




















































Thanks for contributing an answer to Super User!


  • Please be sure to answer the question. Provide details and share your research!

But avoid



  • Asking for help, clarification, or responding to other answers.

  • Making statements based on opinion; back them up with references or personal experience.


To learn more, see our tips on writing great answers.





Some of your past answers have not been well-received, and you're in danger of being blocked from answering.


Please pay close attention to the following guidance:


  • Please be sure to answer the question. Provide details and share your research!

But avoid



  • Asking for help, clarification, or responding to other answers.

  • Making statements based on opinion; back them up with references or personal experience.


To learn more, see our tips on writing great answers.




draft saved


draft discarded














StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fsuperuser.com%2fquestions%2f1381492%2fwhy-does-windows-10-fail-to-install-on-uefi-gpt-laptop%23new-answer', 'question_page');
}
);

Post as a guest















Required, but never shown





















































Required, but never shown














Required, but never shown












Required, but never shown







Required, but never shown

































Required, but never shown














Required, but never shown












Required, but never shown







Required, but never shown







Popular posts from this blog

Сан-Квентин

Алькесар

Josef Freinademetz