What are the metal inserts which accept adjustable screws called?
up vote
3
down vote
favorite
I was watching a woodworking YouTube video which showed a metal insert being permanently hammered into a pre-drilled hole at the bottom of a table leg. A large machine screw with a padded head was then threaded through an opening in the insert and into the pre-drilled hole. The result provided an adjustable foot for the leg which could extend the length of the total leg by up to about an inch.
Here is a bad drawing of what the insert looked like in the video...
My question is what are these inserts called? I want to order some but don't know what to look for.
hardware-identification
asked Nov 25 at 3:30
Henry Taylor
1434
add a comment |
up vote
3
down vote
favorite
I was watching a woodworking YouTube video which showed a metal insert being permanently hammered into a pre-drilled hole at the bottom of a table leg. A large machine screw with a padded head was then threaded through an opening in the insert and into the pre-drilled hole. The result provided an adjustable foot for the leg which could extend the length of the total leg by up to about an inch.
Here is a bad drawing of what the insert looked like in the video...
My question is what are these inserts called? I want to order some but don't know what to look for.
hardware-identification
asked Nov 25 at 3:30
Henry Taylor
1434
add a comment |
up vote
3
down vote
favorite
up vote
3
down vote
favorite
I was watching a woodworking YouTube video which showed a metal insert being permanently hammered into a pre-drilled hole at the bottom of a table leg. A large machine screw with a padded head was then threaded through an opening in the insert and into the pre-drilled hole. The result provided an adjustable foot for the leg which could extend the length of the total leg by up to about an inch.
Here is a bad drawing of what the insert looked like in the video...
My question is what are these inserts called? I want to order some but don't know what to look for.
hardware-identification
asked Nov 25 at 3:30
Henry Taylor
1434
I was watching a woodworking YouTube video which showed a metal insert being permanently hammered into a pre-drilled hole at the bottom of a table leg. A large machine screw with a padded head was then threaded through an opening in the insert and into the pre-drilled hole. The result provided an adjustable foot for the leg which could extend the length of the total leg by up to about an inch.
Here is a bad drawing of what the insert looked like in the video...
My question is what are these inserts called? I want to order some but don't know what to look for.
hardware-identification
hardware-identification
asked Nov 25 at 3:30
Henry Taylor
1434
asked Nov 25 at 3:30
Henry Taylor
1434
asked Nov 25 at 3:30
Henry Taylor
1434
asked Nov 25 at 3:30
Henry Taylor
1434
asked Nov 25 at 3:30
Henry Taylor
1434
1434
add a comment |
add a comment |
1 Answer
1
active
oldest
votes
up vote
7
down vote
accepted
The ones in your sketch are T-nuts, and are typically hammered into the wood. The prongs bite into the wood, keeping it from moving, and the inside of the barrel is threaded to accept a bolt.
Another commonly-used piece of hardware that performs a similar function is a threaded insert. These have threads on the outside of the barrel as well, and are screwed into a hole in the wood. The threads on the outside bite into the wood, keeping it from moving, although some people will also put a small amount of epoxy in there, too.
From what I can see, there's not a whole lot different about them other than the size. T-nuts require a bit more wood around the hole to provide a place for the prongs to bite into. Thus, threaded inserts can be used on smaller pieces of wood than T-nuts (e.g. end or edge grain of 3/4" or 4/4 material). Threaded inserts seem to be more common in knockdown furniture whereas T-nuts seem to be more common in "mechanical" builds (knobs, jigs, etc), although that's just based on me watching woodworking videos on youtube and nothing concrete.
Links are for example only, and are not an endorsement or recommendation.
answered Nov 25 at 4:14
mmathis
2,067530
Thanks! That is exactly the information I was looking for.
– Henry Taylor
Nov 25 at 4:20
1
The other important distinction is that T-nuts can ONLY be used in through-hole applications. The fastener has to be coming into the opposite side of the material the T-nut is attached to, so that the nut is pulled into the material by the fastener. Inserts do not have this limitation, though they are more difficult to insert (i.e. you'll need an impact driver to put one in hardwood) and have less material anchoring them (i.e. they may pull out easier in extremely soft materials).
– SaSSafraS1232
Nov 27 at 21:23
Also, in my experience threaded inserts seem to be made of more durable material than T-nuts. Stripping T-nuts is fairly common, but I've never stripped an insert.
– SaSSafraS1232
Nov 27 at 21:24
add a comment |
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
up vote
7
down vote
accepted
The ones in your sketch are T-nuts, and are typically hammered into the wood. The prongs bite into the wood, keeping it from moving, and the inside of the barrel is threaded to accept a bolt.
Another commonly-used piece of hardware that performs a similar function is a threaded insert. These have threads on the outside of the barrel as well, and are screwed into a hole in the wood. The threads on the outside bite into the wood, keeping it from moving, although some people will also put a small amount of epoxy in there, too.
From what I can see, there's not a whole lot different about them other than the size. T-nuts require a bit more wood around the hole to provide a place for the prongs to bite into. Thus, threaded inserts can be used on smaller pieces of wood than T-nuts (e.g. end or edge grain of 3/4" or 4/4 material). Threaded inserts seem to be more common in knockdown furniture whereas T-nuts seem to be more common in "mechanical" builds (knobs, jigs, etc), although that's just based on me watching woodworking videos on youtube and nothing concrete.
Links are for example only, and are not an endorsement or recommendation.
answered Nov 25 at 4:14
mmathis
2,067530
Thanks! That is exactly the information I was looking for.
– Henry Taylor
Nov 25 at 4:20
1
The other important distinction is that T-nuts can ONLY be used in through-hole applications. The fastener has to be coming into the opposite side of the material the T-nut is attached to, so that the nut is pulled into the material by the fastener. Inserts do not have this limitation, though they are more difficult to insert (i.e. you'll need an impact driver to put one in hardwood) and have less material anchoring them (i.e. they may pull out easier in extremely soft materials).
– SaSSafraS1232
Nov 27 at 21:23
Also, in my experience threaded inserts seem to be made of more durable material than T-nuts. Stripping T-nuts is fairly common, but I've never stripped an insert.
– SaSSafraS1232
Nov 27 at 21:24
add a comment |
up vote
7
down vote
accepted
The ones in your sketch are T-nuts, and are typically hammered into the wood. The prongs bite into the wood, keeping it from moving, and the inside of the barrel is threaded to accept a bolt.
Another commonly-used piece of hardware that performs a similar function is a threaded insert. These have threads on the outside of the barrel as well, and are screwed into a hole in the wood. The threads on the outside bite into the wood, keeping it from moving, although some people will also put a small amount of epoxy in there, too.
From what I can see, there's not a whole lot different about them other than the size. T-nuts require a bit more wood around the hole to provide a place for the prongs to bite into. Thus, threaded inserts can be used on smaller pieces of wood than T-nuts (e.g. end or edge grain of 3/4" or 4/4 material). Threaded inserts seem to be more common in knockdown furniture whereas T-nuts seem to be more common in "mechanical" builds (knobs, jigs, etc), although that's just based on me watching woodworking videos on youtube and nothing concrete.
Links are for example only, and are not an endorsement or recommendation.
answered Nov 25 at 4:14
mmathis
2,067530
Thanks! That is exactly the information I was looking for.
– Henry Taylor
Nov 25 at 4:20
1
The other important distinction is that T-nuts can ONLY be used in through-hole applications. The fastener has to be coming into the opposite side of the material the T-nut is attached to, so that the nut is pulled into the material by the fastener. Inserts do not have this limitation, though they are more difficult to insert (i.e. you'll need an impact driver to put one in hardwood) and have less material anchoring them (i.e. they may pull out easier in extremely soft materials).
– SaSSafraS1232
Nov 27 at 21:23
Also, in my experience threaded inserts seem to be made of more durable material than T-nuts. Stripping T-nuts is fairly common, but I've never stripped an insert.
– SaSSafraS1232
Nov 27 at 21:24
add a comment |
up vote
7
down vote
accepted
up vote
7
down vote
accepted
The ones in your sketch are T-nuts, and are typically hammered into the wood. The prongs bite into the wood, keeping it from moving, and the inside of the barrel is threaded to accept a bolt.
Another commonly-used piece of hardware that performs a similar function is a threaded insert. These have threads on the outside of the barrel as well, and are screwed into a hole in the wood. The threads on the outside bite into the wood, keeping it from moving, although some people will also put a small amount of epoxy in there, too.
From what I can see, there's not a whole lot different about them other than the size. T-nuts require a bit more wood around the hole to provide a place for the prongs to bite into. Thus, threaded inserts can be used on smaller pieces of wood than T-nuts (e.g. end or edge grain of 3/4" or 4/4 material). Threaded inserts seem to be more common in knockdown furniture whereas T-nuts seem to be more common in "mechanical" builds (knobs, jigs, etc), although that's just based on me watching woodworking videos on youtube and nothing concrete.
Links are for example only, and are not an endorsement or recommendation.
answered Nov 25 at 4:14
mmathis
2,067530
The ones in your sketch are T-nuts, and are typically hammered into the wood. The prongs bite into the wood, keeping it from moving, and the inside of the barrel is threaded to accept a bolt.
Another commonly-used piece of hardware that performs a similar function is a threaded insert. These have threads on the outside of the barrel as well, and are screwed into a hole in the wood. The threads on the outside bite into the wood, keeping it from moving, although some people will also put a small amount of epoxy in there, too.
From what I can see, there's not a whole lot different about them other than the size. T-nuts require a bit more wood around the hole to provide a place for the prongs to bite into. Thus, threaded inserts can be used on smaller pieces of wood than T-nuts (e.g. end or edge grain of 3/4" or 4/4 material). Threaded inserts seem to be more common in knockdown furniture whereas T-nuts seem to be more common in "mechanical" builds (knobs, jigs, etc), although that's just based on me watching woodworking videos on youtube and nothing concrete.
Links are for example only, and are not an endorsement or recommendation.
answered Nov 25 at 4:14
mmathis
2,067530
answered Nov 25 at 4:14
mmathis
2,067530
answered Nov 25 at 4:14
mmathis
2,067530
answered Nov 25 at 4:14
mmathis
2,067530
2,067530
Thanks! That is exactly the information I was looking for.
– Henry Taylor
Nov 25 at 4:20
1
The other important distinction is that T-nuts can ONLY be used in through-hole applications. The fastener has to be coming into the opposite side of the material the T-nut is attached to, so that the nut is pulled into the material by the fastener. Inserts do not have this limitation, though they are more difficult to insert (i.e. you'll need an impact driver to put one in hardwood) and have less material anchoring them (i.e. they may pull out easier in extremely soft materials).
– SaSSafraS1232
Nov 27 at 21:23
Also, in my experience threaded inserts seem to be made of more durable material than T-nuts. Stripping T-nuts is fairly common, but I've never stripped an insert.
– SaSSafraS1232
Nov 27 at 21:24
add a comment |
Thanks! That is exactly the information I was looking for.
– Henry Taylor
Nov 25 at 4:20
1
The other important distinction is that T-nuts can ONLY be used in through-hole applications. The fastener has to be coming into the opposite side of the material the T-nut is attached to, so that the nut is pulled into the material by the fastener. Inserts do not have this limitation, though they are more difficult to insert (i.e. you'll need an impact driver to put one in hardwood) and have less material anchoring them (i.e. they may pull out easier in extremely soft materials).
– SaSSafraS1232
Nov 27 at 21:23
Also, in my experience threaded inserts seem to be made of more durable material than T-nuts. Stripping T-nuts is fairly common, but I've never stripped an insert.
– SaSSafraS1232
Nov 27 at 21:24
Thanks! That is exactly the information I was looking for.
– Henry Taylor
Nov 25 at 4:20
Thanks! That is exactly the information I was looking for.
– Henry Taylor
Nov 25 at 4:20
1
1
The other important distinction is that T-nuts can ONLY be used in through-hole applications. The fastener has to be coming into the opposite side of the material the T-nut is attached to, so that the nut is pulled into the material by the fastener. Inserts do not have this limitation, though they are more difficult to insert (i.e. you'll need an impact driver to put one in hardwood) and have less material anchoring them (i.e. they may pull out easier in extremely soft materials).
– SaSSafraS1232
Nov 27 at 21:23
The other important distinction is that T-nuts can ONLY be used in through-hole applications. The fastener has to be coming into the opposite side of the material the T-nut is attached to, so that the nut is pulled into the material by the fastener. Inserts do not have this limitation, though they are more difficult to insert (i.e. you'll need an impact driver to put one in hardwood) and have less material anchoring them (i.e. they may pull out easier in extremely soft materials).
– SaSSafraS1232
Nov 27 at 21:23
Also, in my experience threaded inserts seem to be made of more durable material than T-nuts. Stripping T-nuts is fairly common, but I've never stripped an insert.
– SaSSafraS1232
Nov 27 at 21:24
Also, in my experience threaded inserts seem to be made of more durable material than T-nuts. Stripping T-nuts is fairly common, but I've never stripped an insert.
– SaSSafraS1232
Nov 27 at 21:24
add a comment |
Thanks for contributing an answer to Woodworking Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fwoodworking.stackexchange.com%2fquestions%2f8017%2fwhat-are-the-metal-inserts-which-accept-adjustable-screws-called%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
