Filament extrusion always stops at some point during print
$begingroup$
I own a Creality CR-10 (using Ultimaker Cura for slicing) and I am experiencing terrible printing problems.
My problem: I am not able to print anything that takes several hours to print. For parts printed in 30 minutes or so, my printer usually works.
The prints end up like this (unfinished and with a lot of stringing)
This below is actually the best result I got so far.. (important note: there is no under extrusion during the print, it suddenly stops out of nowhere..)
(Although I have to use terrible retraction settings and need a lot of post processing because of all the stringing - you might have an answer for that too.. I just couldnt get the 3d printer to print parts properly with good retraction settings.)
The problem is that at some point of the print, no more (PLA) material is extruded and the printer moves without actually printing anything. The first couple of layers usually work (you can see that in the images) but after wasting almost 600 grams of PLA, I am not able to find a solution myself.
.
I have some suspicions:
Could the problem be the angle, the PLA is inserted into the feeder? (so that it is almost a 90 degree bend)? The filament comes from a spool in the right hand side. But I dont think that this would cause such a problem..
Is it a software problem? Here are all my cura settings (I even reduced the printing speed to 30mm/s at 205°C - still didnt work..) :-(
Could the length of the bowden tube and it tangling up be a problem? (as you can see in the image below)
And annother important thing: The feeder always grinds into the filament (even at those low retraction settings) and it is always very hard to pull the filament out of the bowden after a failed print. Sometimes its almost impossible and i have to use heavy tools for it.. that should be the probelem
I already did some atomic pulls, replaced the nozzle and switched the bowden tube.
I have a dream: My printer printing a part without any stringing and actually finishing the print. Please help me to achieve this dream..
Thank you for your help in advance. :)
(and the filament I used, sorry for the bad quality of the pic)
print-quality filament pla cr-10
edited 15 hours ago
0scar
10.5k21446
asked 16 hours ago
DonaldEnteDonaldEnte
1206
$endgroup$
add a comment |
$begingroup$
I own a Creality CR-10 (using Ultimaker Cura for slicing) and I am experiencing terrible printing problems.
My problem: I am not able to print anything that takes several hours to print. For parts printed in 30 minutes or so, my printer usually works.
The prints end up like this (unfinished and with a lot of stringing)
This below is actually the best result I got so far.. (important note: there is no under extrusion during the print, it suddenly stops out of nowhere..)
(Although I have to use terrible retraction settings and need a lot of post processing because of all the stringing - you might have an answer for that too.. I just couldnt get the 3d printer to print parts properly with good retraction settings.)
The problem is that at some point of the print, no more (PLA) material is extruded and the printer moves without actually printing anything. The first couple of layers usually work (you can see that in the images) but after wasting almost 600 grams of PLA, I am not able to find a solution myself.
.
I have some suspicions:
Could the problem be the angle, the PLA is inserted into the feeder? (so that it is almost a 90 degree bend)? The filament comes from a spool in the right hand side. But I dont think that this would cause such a problem..
Is it a software problem? Here are all my cura settings (I even reduced the printing speed to 30mm/s at 205°C - still didnt work..) :-(
Could the length of the bowden tube and it tangling up be a problem? (as you can see in the image below)
And annother important thing: The feeder always grinds into the filament (even at those low retraction settings) and it is always very hard to pull the filament out of the bowden after a failed print. Sometimes its almost impossible and i have to use heavy tools for it.. that should be the probelem
I already did some atomic pulls, replaced the nozzle and switched the bowden tube.
I have a dream: My printer printing a part without any stringing and actually finishing the print. Please help me to achieve this dream..
Thank you for your help in advance. :)
(and the filament I used, sorry for the bad quality of the pic)
print-quality filament pla cr-10
edited 15 hours ago
0scar
10.5k21446
asked 16 hours ago
DonaldEnteDonaldEnte
1206
$endgroup$
add a comment |
$begingroup$
I own a Creality CR-10 (using Ultimaker Cura for slicing) and I am experiencing terrible printing problems.
My problem: I am not able to print anything that takes several hours to print. For parts printed in 30 minutes or so, my printer usually works.
The prints end up like this (unfinished and with a lot of stringing)
This below is actually the best result I got so far.. (important note: there is no under extrusion during the print, it suddenly stops out of nowhere..)
(Although I have to use terrible retraction settings and need a lot of post processing because of all the stringing - you might have an answer for that too.. I just couldnt get the 3d printer to print parts properly with good retraction settings.)
The problem is that at some point of the print, no more (PLA) material is extruded and the printer moves without actually printing anything. The first couple of layers usually work (you can see that in the images) but after wasting almost 600 grams of PLA, I am not able to find a solution myself.
.
I have some suspicions:
Could the problem be the angle, the PLA is inserted into the feeder? (so that it is almost a 90 degree bend)? The filament comes from a spool in the right hand side. But I dont think that this would cause such a problem..
Is it a software problem? Here are all my cura settings (I even reduced the printing speed to 30mm/s at 205°C - still didnt work..) :-(
Could the length of the bowden tube and it tangling up be a problem? (as you can see in the image below)
And annother important thing: The feeder always grinds into the filament (even at those low retraction settings) and it is always very hard to pull the filament out of the bowden after a failed print. Sometimes its almost impossible and i have to use heavy tools for it.. that should be the probelem
I already did some atomic pulls, replaced the nozzle and switched the bowden tube.
I have a dream: My printer printing a part without any stringing and actually finishing the print. Please help me to achieve this dream..
Thank you for your help in advance. :)
(and the filament I used, sorry for the bad quality of the pic)
print-quality filament pla cr-10
edited 15 hours ago
0scar
10.5k21446
asked 16 hours ago
DonaldEnteDonaldEnte
1206
$endgroup$
I own a Creality CR-10 (using Ultimaker Cura for slicing) and I am experiencing terrible printing problems.
My problem: I am not able to print anything that takes several hours to print. For parts printed in 30 minutes or so, my printer usually works.
The prints end up like this (unfinished and with a lot of stringing)
This below is actually the best result I got so far.. (important note: there is no under extrusion during the print, it suddenly stops out of nowhere..)
(Although I have to use terrible retraction settings and need a lot of post processing because of all the stringing - you might have an answer for that too.. I just couldnt get the 3d printer to print parts properly with good retraction settings.)
The problem is that at some point of the print, no more (PLA) material is extruded and the printer moves without actually printing anything. The first couple of layers usually work (you can see that in the images) but after wasting almost 600 grams of PLA, I am not able to find a solution myself.
.
I have some suspicions:
Could the problem be the angle, the PLA is inserted into the feeder? (so that it is almost a 90 degree bend)? The filament comes from a spool in the right hand side. But I dont think that this would cause such a problem..
Is it a software problem? Here are all my cura settings (I even reduced the printing speed to 30mm/s at 205°C - still didnt work..) :-(
Could the length of the bowden tube and it tangling up be a problem? (as you can see in the image below)
And annother important thing: The feeder always grinds into the filament (even at those low retraction settings) and it is always very hard to pull the filament out of the bowden after a failed print. Sometimes its almost impossible and i have to use heavy tools for it.. that should be the probelem
I already did some atomic pulls, replaced the nozzle and switched the bowden tube.
I have a dream: My printer printing a part without any stringing and actually finishing the print. Please help me to achieve this dream..
Thank you for your help in advance. :)
(and the filament I used, sorry for the bad quality of the pic)
print-quality filament pla cr-10
print-quality filament pla cr-10
edited 15 hours ago
0scar
10.5k21446
asked 16 hours ago
DonaldEnteDonaldEnte
1206
edited 15 hours ago
0scar
10.5k21446
asked 16 hours ago
DonaldEnteDonaldEnte
1206
edited 15 hours ago
0scar
10.5k21446
edited 15 hours ago
0scar
10.5k21446
edited 15 hours ago
0scar
10.5k21446
10.5k21446
asked 16 hours ago
DonaldEnteDonaldEnte
1206
asked 16 hours ago
DonaldEnteDonaldEnte
1206
asked 16 hours ago
DonaldEnteDonaldEnte
1206
1206
add a comment |
add a comment |
1 Answer
1
active
oldest
votes
$begingroup$
Stringing?
The stringing is explained by your relatively low retraction settings, 1.5 mm is not much for a Bowden setup. As do too high printing temperatures.
Stopping mid printing?
What you are experiencing is called clogging, the extruder cannot push the filament through the hotend and cause the grinding you report. Clogging mid printing is usually caused by insufficient cooling (for the temperature you print at) of the cold end (causing heat creep; slowly increasing temperature of the heat break), especially all-metal hotend assemblies are notoriously known for this problem.
Your Bowden tube does make a lot of kinks, maybe you can improve the path of the Bowden tube. Also if you are concerned about the sharp filament intake angle, you could print a filament guide:
answered 15 hours ago
0scar0scar
10.5k21446
$endgroup$
$begingroup$
Thank you, I will try to fix those things. Do you think my problem is software related or is it the hardware? I can only fix this issue by buying a new hotend?
$endgroup$
– DonaldEnte
15 hours ago
3
$begingroup$
@DonaldEnte - Get known issues fixed first, then move onto the next problem (if there is a "next problem*). I'm betting your main issues are mechanical having to do mainly with the Bowden tube and how it is run ... that's some pretty healthy kinking going on there.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
15 hours ago
1
$begingroup$
Clogging implies heat creep, and heat creep implies overly hot printing temperature (assuming that the heat break cooling is vaguely normal). Printing too hot can also cause excessive stringing, so reducing print temp might kill two birds with one stone.
$endgroup$
– anaximander
13 hours ago
add a comment |
Your Answer
StackExchange.ifUsing("editor", function () {
return StackExchange.using("mathjaxEditing", function () {
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["$", "$"], ["\\(","\\)"]]);
});
});
}, "mathjax-editing");
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "640"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2f3dprinting.stackexchange.com%2fquestions%2f7992%2ffilament-extrusion-always-stops-at-some-point-during-print%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
$begingroup$
Stringing?
The stringing is explained by your relatively low retraction settings, 1.5 mm is not much for a Bowden setup. As do too high printing temperatures.
Stopping mid printing?
What you are experiencing is called clogging, the extruder cannot push the filament through the hotend and cause the grinding you report. Clogging mid printing is usually caused by insufficient cooling (for the temperature you print at) of the cold end (causing heat creep; slowly increasing temperature of the heat break), especially all-metal hotend assemblies are notoriously known for this problem.
Your Bowden tube does make a lot of kinks, maybe you can improve the path of the Bowden tube. Also if you are concerned about the sharp filament intake angle, you could print a filament guide:
answered 15 hours ago
0scar0scar
10.5k21446
$endgroup$
$begingroup$
Thank you, I will try to fix those things. Do you think my problem is software related or is it the hardware? I can only fix this issue by buying a new hotend?
$endgroup$
– DonaldEnte
15 hours ago
3
$begingroup$
@DonaldEnte - Get known issues fixed first, then move onto the next problem (if there is a "next problem*). I'm betting your main issues are mechanical having to do mainly with the Bowden tube and how it is run ... that's some pretty healthy kinking going on there.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
15 hours ago
1
$begingroup$
Clogging implies heat creep, and heat creep implies overly hot printing temperature (assuming that the heat break cooling is vaguely normal). Printing too hot can also cause excessive stringing, so reducing print temp might kill two birds with one stone.
$endgroup$
– anaximander
13 hours ago
add a comment |
$begingroup$
Stringing?
The stringing is explained by your relatively low retraction settings, 1.5 mm is not much for a Bowden setup. As do too high printing temperatures.
Stopping mid printing?
What you are experiencing is called clogging, the extruder cannot push the filament through the hotend and cause the grinding you report. Clogging mid printing is usually caused by insufficient cooling (for the temperature you print at) of the cold end (causing heat creep; slowly increasing temperature of the heat break), especially all-metal hotend assemblies are notoriously known for this problem.
Your Bowden tube does make a lot of kinks, maybe you can improve the path of the Bowden tube. Also if you are concerned about the sharp filament intake angle, you could print a filament guide:
answered 15 hours ago
0scar0scar
10.5k21446
$endgroup$
$begingroup$
Thank you, I will try to fix those things. Do you think my problem is software related or is it the hardware? I can only fix this issue by buying a new hotend?
$endgroup$
– DonaldEnte
15 hours ago
3
$begingroup$
@DonaldEnte - Get known issues fixed first, then move onto the next problem (if there is a "next problem*). I'm betting your main issues are mechanical having to do mainly with the Bowden tube and how it is run ... that's some pretty healthy kinking going on there.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
15 hours ago
1
$begingroup$
Clogging implies heat creep, and heat creep implies overly hot printing temperature (assuming that the heat break cooling is vaguely normal). Printing too hot can also cause excessive stringing, so reducing print temp might kill two birds with one stone.
$endgroup$
– anaximander
13 hours ago
add a comment |
$begingroup$
Stringing?
The stringing is explained by your relatively low retraction settings, 1.5 mm is not much for a Bowden setup. As do too high printing temperatures.
Stopping mid printing?
What you are experiencing is called clogging, the extruder cannot push the filament through the hotend and cause the grinding you report. Clogging mid printing is usually caused by insufficient cooling (for the temperature you print at) of the cold end (causing heat creep; slowly increasing temperature of the heat break), especially all-metal hotend assemblies are notoriously known for this problem.
Your Bowden tube does make a lot of kinks, maybe you can improve the path of the Bowden tube. Also if you are concerned about the sharp filament intake angle, you could print a filament guide:
answered 15 hours ago
0scar0scar
10.5k21446
$endgroup$
Stringing?
The stringing is explained by your relatively low retraction settings, 1.5 mm is not much for a Bowden setup. As do too high printing temperatures.
Stopping mid printing?
What you are experiencing is called clogging, the extruder cannot push the filament through the hotend and cause the grinding you report. Clogging mid printing is usually caused by insufficient cooling (for the temperature you print at) of the cold end (causing heat creep; slowly increasing temperature of the heat break), especially all-metal hotend assemblies are notoriously known for this problem.
Your Bowden tube does make a lot of kinks, maybe you can improve the path of the Bowden tube. Also if you are concerned about the sharp filament intake angle, you could print a filament guide:
answered 15 hours ago
0scar0scar
10.5k21446
edited 13 hours ago
answered 15 hours ago
0scar0scar
10.5k21446
answered 15 hours ago
0scar0scar
10.5k21446
answered 15 hours ago
0scar0scar
10.5k21446
10.5k21446
$begingroup$
Thank you, I will try to fix those things. Do you think my problem is software related or is it the hardware? I can only fix this issue by buying a new hotend?
$endgroup$
– DonaldEnte
15 hours ago
3
$begingroup$
@DonaldEnte - Get known issues fixed first, then move onto the next problem (if there is a "next problem*). I'm betting your main issues are mechanical having to do mainly with the Bowden tube and how it is run ... that's some pretty healthy kinking going on there.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
15 hours ago
1
$begingroup$
Clogging implies heat creep, and heat creep implies overly hot printing temperature (assuming that the heat break cooling is vaguely normal). Printing too hot can also cause excessive stringing, so reducing print temp might kill two birds with one stone.
$endgroup$
– anaximander
13 hours ago
add a comment |
$begingroup$
Thank you, I will try to fix those things. Do you think my problem is software related or is it the hardware? I can only fix this issue by buying a new hotend?
$endgroup$
– DonaldEnte
15 hours ago
3
$begingroup$
@DonaldEnte - Get known issues fixed first, then move onto the next problem (if there is a "next problem*). I'm betting your main issues are mechanical having to do mainly with the Bowden tube and how it is run ... that's some pretty healthy kinking going on there.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
15 hours ago
1
$begingroup$
Clogging implies heat creep, and heat creep implies overly hot printing temperature (assuming that the heat break cooling is vaguely normal). Printing too hot can also cause excessive stringing, so reducing print temp might kill two birds with one stone.
$endgroup$
– anaximander
13 hours ago
$begingroup$
Thank you, I will try to fix those things. Do you think my problem is software related or is it the hardware? I can only fix this issue by buying a new hotend?
$endgroup$
– DonaldEnte
15 hours ago
$begingroup$
Thank you, I will try to fix those things. Do you think my problem is software related or is it the hardware? I can only fix this issue by buying a new hotend?
$endgroup$
– DonaldEnte
15 hours ago
3
3
$begingroup$
@DonaldEnte - Get known issues fixed first, then move onto the next problem (if there is a "next problem*). I'm betting your main issues are mechanical having to do mainly with the Bowden tube and how it is run ... that's some pretty healthy kinking going on there.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
15 hours ago
$begingroup$
@DonaldEnte - Get known issues fixed first, then move onto the next problem (if there is a "next problem*). I'm betting your main issues are mechanical having to do mainly with the Bowden tube and how it is run ... that's some pretty healthy kinking going on there.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
15 hours ago
1
1
$begingroup$
Clogging implies heat creep, and heat creep implies overly hot printing temperature (assuming that the heat break cooling is vaguely normal). Printing too hot can also cause excessive stringing, so reducing print temp might kill two birds with one stone.
$endgroup$
– anaximander
13 hours ago
$begingroup$
Clogging implies heat creep, and heat creep implies overly hot printing temperature (assuming that the heat break cooling is vaguely normal). Printing too hot can also cause excessive stringing, so reducing print temp might kill two birds with one stone.
$endgroup$
– anaximander
13 hours ago
add a comment |
Thanks for contributing an answer to 3D Printing Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2f3dprinting.stackexchange.com%2fquestions%2f7992%2ffilament-extrusion-always-stops-at-some-point-during-print%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
